Mechanical Testing 1
Aim: Understand mechanical testing methods, including tensile testing and hardness testing.
This resource includes:
Session Power-point file (16 slides)
Testing of Materials handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Mechanical Testing 2
Aim: Explore how to interpret results from mechanical testing.
This resource includes:
Session Power-point file (14 slides)
Testing Materials Instruction activity Handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Introduction to Engineering and Manufacturing Design
This resource is part of the set for “Working In Engineering”
Aim: Understand key principles and methodologies in engineering and manufacturing design.
This resource includes:
Session Power-point file (21 slides)
Initial Assessment Paper
Initial Assessment Marking Scheme
Information Sheet
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Summative Assessment paper
Aim: Carry out the final assessment and address any areas of difficulty.
This resource includes:
Session Power-point file (4 slides with exam conditions written on them)
Summative Assessment of Engineering Materials - Exam Paper
Summative Assessment of Engineering Materials - Marking Guide
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Testing and Visual inspection 1
Aim: Understand the different testing methods used for material evaluation.
This resource includes:
Session Power-point file (12 slides)
NDT and Visual Detection Handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Fitness for Purpose
This resource is part of the set for “Working In Engineering”
Aim: Understand how fitness for purpose influence design decisions.
This resource includes:
Session Power-point file (12 slides)
Case study handout
Information Handout
Products Activity Handout
Peer assessment feedback handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Composite Processing 2
Aim: Explore the influence of matrix/reinforcement ratio on composite tensile strength.
This resource includes:
Session Power-point file (13 slides)
Composite Analysis Handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Material Failure Corrosion 1
Aim: Understand the various causes of material failure, including corrosion.
This resource includes:
Session Power-point file (13 slides)
Types of corrosion Handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Testing and Visual inspection 2
Aim: Learn to interpret results from visual inspection and non-destructive testing.
This resource includes:
Session Power-point file (13 slides)
Evaluation of NDT Handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Surface Treatments 2
Aim: Explore the benefits and limitations of various surface treatment methods.
This resource includes:
Session Power-point file (22 slides)
Electroplating Task Handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Types of Manufacturing
This resource is part of the set for “Working In Engineering”
Aim: Learn about different types of manufacturing processes and their influence on product design.
This resource includes:
Session Power-point file (30 slides)
Joining Metals handout
Casting methods Handout
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Material Failure Aging and Physical 2
Aim: Explore preventive measures against aging and physical failures.
This resource includes:
Session Power-point file (12 slides)
Question Paper
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Arithmetic and Geometric Progressions
This resource is part of the set for “Essential mathematics for engineering and manufacturing”
Aim: Understand arithmetic and geometric progressions and their use in engineering contexts.
This resource includes:
Session Power-point file (13 slides)
Geometric Progression Information Sheet
Geometric Progression Method Sheet
Geometric Progression Task sheet
Geometric Progression PDF
Geometric Progression Teacher Copy
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Geometry: Areas and Volumes 2
This resource is part of the set for “Essential mathematics for engineering and manufacturing”
Aim: Apply geometry concepts to practical engineering scenarios.
This resource includes:
Session Power-point file (13 slides)
Applied Geometry Problems
Applied Geometry Problems PDF
Applied Geometry Problems Teacher Copy
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Graphs and Charts
This resource is part of the set for “Essential mathematics for engineering and manufacturing”
Aim: Interpret and express changes in an engineering system from a graph.
This resource includes:
Session Power-point file (14 slides)
Graph Types in Engineering
Graph Types in Engineering PDF
Graph Formulas in Engineering Task
Graph Formulas in Engineering Task PDF
Graph Formulas in Engineering Teacher copy
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Geometry: Areas and Volumes 1
This resource is part of the set for “Essential mathematics for engineering and manufacturing”
Aim: Calculate the area of 2D shapes (square, rectangle, triangle, circle) and the volume of 3D shapes (cube, cuboid, cylinder, cone).
This resource includes:
Session Power-point file (22 slides)
Geometric Areas Questions
Geometric Areas Questions PDF
Geometric Areas Questions Teacher Copy
Geometric Volumes Questions
Geometric Volumes Questions PDF
Geometric Volumes Questions Teacher Copy
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Calculus: Differentiation 1
This resource is part of the set for “Essential mathematics for engineering and manufacturing”
Aim: Determine standard differentials and use differentiation to calculate maximum and minimum values in engineering contexts.
This resource includes:
Session Power-point file (14 slides)
Calculus Differentiation Steps - Helpsheet
Calculus - Critical points tasks
Calculus - Critical points PDF
Calculus - Critical points Teacher Copy
Calculus Derivatives Information sheet
Calculus Derivative Tasks
Calculus Derivative PDF
Calculus Derivatives Teacher Copy
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Calculus: Differentiation 2
This resource is part of the set for “Essential mathematics for engineering and manufacturing”
Aim: Learn to find the equation of a tangent to a curve in engineering contexts.
This resource includes:
Session Power-point file (14 slides)
Tangent Line Information
Real world examples of Calculus
Calculus Problems Task
Calculus Problems Task PDF
Calculus Problems Teacher Copy
Calculus - Challenging Problems task
Calculus - Challenging Problems PDF
Calculus - Challenging Problems Teacher copy
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Introduction to Applied Mathematical Theory in Engineering Applications
This resource is part of the set for “Essential mathematics for engineering and manufacturing”
Aim: Understand the importance of mathematics in engineering and manufacturing.
This resource includes:
Session Power-point file (13 slides)
Initial Assessment Task
Initial Assessment Task PDF
Initial Assessment Task Teacher Copy with Answers
BIDMAS Questions
BIDMAS Questions PDF
Bidmas Questions Teacher Copy
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.
Percentages and ratios
This resource is part of the set for “Essential mathematics for engineering and manufacturing”
Aim: Apply percentages and ratios to scale calculations.
This resource includes:
Session Power-point file (18 slides)
Percentages Helpsheet
Percentages Task sheet
Percentages Task sheet PDF
Percentages Teacher Copy
Ratios Question Sheet
Ratios Question Sheet PDF
Ratios Question Sheet Teacher Copy
Please feel free to check out our other resources, over the next academic year we will be adding a whole host of resources to support teaching Engineering.