Our resources aim to give Design & Technology teachers and students a clear understanding of the requirements of the new specification GCSE Design and Technology course. The resources available from ACA Resources provide complete coverage of all theory required for the exam, as well as comprehensive guidance for the Non-exam assessment.
Our resources aim to give Design & Technology teachers and students a clear understanding of the requirements of the new specification GCSE Design and Technology course. The resources available from ACA Resources provide complete coverage of all theory required for the exam, as well as comprehensive guidance for the Non-exam assessment.
The board game tests students’ knowledge on all aspects of the knowledge required for the final exam.
The students will be able to learn or revise through competition and fun!
Although the knowledge is GCSE level, the game can be played by students across KS3 and KS4, ensuring that students are fully prepared for GCSE D&T, and understand exactly what they need to know.
The game is broken down into sections and sub-sections, aligned with the DT teaching resources available at ACA Resources on TES
https://www.tes.com/teaching-resources/shop/ACAResources
The knowledge organisers (available from ACA Resources) provide a basis for learning and revising key information required to answer the questions. The learning in the knowledge organisers is the knowledge required for the final D&T exam.
Students will answer questions on each sub section to progress around the board to the finish.
The game can be played as individuals or in teams.
Game type 1:
Each team takes it in turns to answer a question from the segment on which their playing piece stands.
If they answer their question correctly, they advance onto the next segment and will then answer a question from this category on their next turn.
If they fail to answer correctly they remain on the same segment and answer a question from the same category on their next turn.
Play continues until one team reaches the finish
Game type 2: (Quicker game)
One player from the team asks a question to their team mates, from the section on which their playing piece stands.
If their team answers correctly they advance onto the next square and another question is immediately asked from this next category.
The team must answer as many questions correctly as possible within 30 seconds and will advance by one square for each correct answer.
Game type 3: (keeping both teams in the same category)
Same rules as game type 1, however the first team to reach the end of one complete section is awarded a point, and both teams then start from the beginning of the next section.
The winning team is the team with the most points (complete sections won) by the end of the game
This allows for a time limit to be set, ensuring that all games finish at the same time if multiple games are being played across the class and a tournament or rotation system is being used.
The cards can also be used as a standalone resource as Revision cards, Questioning cues, Lesson start review resource
It is also possible to edit the cards to leave the answers blank, allowing them to be handed out as a review activity.
AQA GCSE Design and Technology - Knowledge Organiser for Designing and Making
Knowledge Organiser containing all of the key words needed in Designing and Making, in preparation for the AQA GCSE Design and Technology exam and Non-Exam Assessment.
The sections in this knowledge organiser are aligned with the sections in the AQA GCSE Design and Technology revision guide by CGP Books.
This knowledge organiser is particularly effective when used in combination with our other theory resources to be found in our store.
Knowledge organisers are also available for all theory sections (Sections 1-5).
AQA GCSE Design and Technology (DT) - Exam Theory - Section 1.2 - Production Systems - CADCAM
This resource contains all of the key knowledge that the students are required to know for Section 1.2 - Production Systems - CADCAM
CAD
CAM
CNC
Subtraction of Material
Addition of Material
2-Axis CAM
3-Axis CAM
Global Communication
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology (DT) - Exam Theory - Section 2.2 - Paper, Board and Timber
This resource contains all of the key knowledge that the students are required to know for Section 2.2 - Paper, Board and Timber
Paper Properties
Cartridge Paper
Layout Paper
Tracing Paper
Grid Paper
Bleed-Proof Paper
Board Types and Uses
Solid White Board
Ink Jet
Corrugated
Duplex
Foam Core
Foil Lined
Hardwood
Softwood
Timber
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology (DT) - Exam Theory - Section 4.1 - Properties of Paper and Board
This resource contains all of the key knowledge that the students are required to know for Section 4.1 - Properties of Paper and Board
Properties
Flexibility
Rigidity
Strength and Weight
Toxicity
Sustainability
Cost and Quality
Board Finishes
Properties for Application
Modification
Chemical Additives
Stock Forms
Paper Differences
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.6 - Shaping Techniques
This resource contains all of the key knowledge that the students are required to know for Section 5.6 - Shaping Techniques
Shaping Techniques
Milling Machines
Lathes
3D Printing
Metal Press
Casting
Die Casting
Bending Materials
Plywood Forming
Line Bender
Strip Heater
Annealing
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology (DT) - Exam Theory - Section 1.6 - Powering Systems
This resource contains all of the key knowledge that the students are required to know for Section 1.6 - Powering Systems
Fossil Fuels
Finite Resources
Non-Finite Resources
Nuclear Power
Renewable Energy
Wind Power
Solar Power
Hydro-electric Power
Tidal Barrages
Biomass
Arguments For and Against Renewable Energy
Batteries
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology (DT) - Exam Theory - Section 2.3 - Metals, Alloys and Polymers
This resource contains all of the key knowledge that the students are required to know for Section 2.3 - Metals, Alloys and Polymers
Ferrous Metals
Cast Iron, Low Carbon Steel, High Carbon Steel
Non-Ferrous Metals
Aluminium, Copper, Tin, Zinc
Alloys
Brass, Stainless Steel
Thermoforming Plastic
Acrylic, HDPE, PET, HIPS, PVC
Thermosetting Plastic
ER, UF, MF, PF, PR
Properties and Uses
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology - Knowledge Organiser for Section 2 - An Introduction to Materials and Systems
Knowledge Organiser containing all of the key words needed in Section 2 - An Introduction to Materials and Systems, in preparation for the AQA GCSE Design and Technology exam.
The sections in this knowledge organiser are aligned with the sections in the AQA GCSE Design and Technology revision guide by CGP Books.
This knowledge organiser is particularly effective when used in combination with our other theory resources to be found in our store.
Knowledge organisers are also available for all other sections (Sections 1-5).
Suggestions for use:
Print out the knowledge organisers as a booklet for your GCSE students. You may also consider creating a version with the descriptions in blank, so that students can use it a a worksheet to test themselves on their knowledge and identify gaps in knowledge.
AQA GCSE Design and Technology (DT) - Exam Theory - Section 4.2 - Standard Components
This resource contains all of the key knowledge that the students are required to know for Section 4.2 - Standard Components
Standard Components
Examples and Uses
Bindings
Seals
Tapes
Adhesives
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.1 - Uses of Woods, Metals and Polymers
This resource contains all of the key knowledge that the students are required to know for Section 5.1 - Uses of Woods, Metals and Polymers
Choosing Materials for Specific Purposes
Modifications
Wood (Timber) Seasoning
Annealing
UV Treatment
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.7 - Moulding and Joining
This resource contains all of the key knowledge that the students are required to know for Section 5.7 - Moulding and Joining
Vacuum Forming
Blow Moulding
Injection Moulding
Extrusion
Gluing
Soldering
Brazing
Welding
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
AQA GCSE Design and Technology - Knowledge Organiser for Section 4 - Paper and Board
Knowledge Organiser containing all of the key words needed in Section 4 - Paper and Board, in preparation for the AQA GCSE Design and Technology exam.
The sections in this knowledge organiser are aligned with the sections in the AQA GCSE Design and Technology revision guide by CGP Books.
This knowledge organiser is particularly effective when used in combination with our other theory resources to be found in our store.
Knowledge organisers are also available for all other sections (Sections 1-5).
Suggestions for use:
Print out the knowledge organisers as a booklet for your GCSE students. You may also consider creating a version with the descriptions in blank, so that students can use it a a worksheet to test themselves on their knowledge and identify gaps in knowledge.
AQA GCSE Design and Technology (DT) - Exam Theory - Section 5.5 - Shaping Materials (Power and Machine Tools)
This resource contains all of the key knowledge that the students are required to know for Section 5.5 - Shaping Materials (Power and Machine Tools)
Safety Steps
Power Tools
Router
Planer
Jigsaw
Sander
Machine Tools
Sanding Disc
Saw Bench
Bandsaw
Pillar Drill
Fences
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students absolute clarity when progressing through the theory required for the exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with a tracker designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity *(particularly effective when used with a tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enchanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (Available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on your tracker (which I recommend you set up, student names down the side, sub-sections along the top).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
A1 sized Knowledge Organiser for AQA GCSE Design and Technology (Including Design and Technology Textiles). Including key words and phrases with pictures and explanations.
AQA GCSE Design and Technology (DT) - Designing and Making - Design Briefs and Specifications
This resource contains all of the key knowledge that the students are required to know for Designing and Making - Design Briefs and Specifications
Design Brief
Research Types
Market Research
Product Analysis
Research Analysis
Design Specification
The sections in these resources align with the sections in the AQA DT revision guide by CGP Books, which gives students clarity and confidence in preparation for both the NEA and the written exam.
These resources have been developed with the following goals in mind:
Allows learners to work through the theory independently, promoting challenge for all learners and ability levels
Disruptive students have less effect on the progress of the learners, as the resources encourage independent learning.
Promotes a love of learning, as learners self-motivate. This is particularly effective when the series of resources is used in combination with the tracker (available for free) designed to show learners their progress through the resources.
Allows independent home learning to be set that follows on and links clearly with the classwork.
Ensures that students have covered all theory required for the exam, with absolute clarity, *(particularly effective when used with the tracker)
Suggested strategy:
This resource is one sub-section. When used as a complete section the following strategy can be adopted:
Begin the lesson by discussion of key words and ideas required in this sub-section. This can be enhanced with related videos from sites such as YouTube.
Encourage students to independently research each concept they come across in the activity by using the internet, CGP revision guide, knowledge organiser (available seperately), peer discussion, teacher discussion etc.
At the end of each resource there are exam-style questions to prepare students for how the knowledge may need to be applied in the exam.
When the sub-section is complete, students get this checked by the teacher and marked off on the tracker (available for free).
The student can then move on to the next sub-section at their own pace, or if you wish to keep the class at the same point, they can act as consultants for the other students in the class, further cementing their knowledge.
These resources have been tested, developed and implemented across our academy and have had a drastic impact on student preparedness for the exam, exam results, and student engagement with the course. The resources can also be used at KS3 in preparation for the GCSE course
GCSE Design and Technology
Theory Section 1 out of 5 (All sections are available)
Section 1 - Key Ideas in Design and Technology
Student Workbook
This workbook comprehensively covers all content from section 1 of the theory, required for the GCSE DT exam.
The workbook can be used as a framework for teaching, as well as for student independent working.
Each section includes worksheets and a knowledge organiser. At the end of the workbook there is also a blank knowledge organiser which can be used to review learning and retention of key knowledge.
Progress can be tracked using the free tracker available from ACA Resources on TES
https://www.tes.com/teaching-resource/aqa-gcse-dt-theory-tracker-12190083
A-Level Design and Technology (Product Design)
Theory Section B (All 9 sections A through to I are also available)
Section B - Advanced Materials
Student Workbook
This workbook comprehensively covers all content from section B of the theory, required for the A-Level DT exams.
B1 - Biodegradable Materials
B2 - Composites
B3 - Smart Materials
B4 - Modern Materials
The workbook can be used as a framework for teaching, as well as for student independent working.
Each sub-section includes worksheets and practice questions to aid retention and understanding of how the content may be presented in the exam.
Progress can be tracked using the free tracker available from ACA Resources on TES.
https://www.tes.com/teaching-resource/a-level-dt-theory-tracker-12396290
The content in this workbook has been designed to meet the demands of the AQA A-level in Design and Technology/ Product Design. The content also closely meets the requirements for Eduqas/WJEC, OCR and Edexcel.
A-Level Design and Technology (Product Design)
Theory Section D (All 9 sections A through to I are also available)
Section D - Industry Requirements and Standards
Student Workbook
This workbook comprehensively covers all content from section D of the theory, required for the A-Level DT exams.
D1 - Modern Industrial and Commercial Practice
D2 - Digital Design and Manufacture
D3 - The Requirements for Product Design and Development
D4 - Health and Safety
D5 - Protecting Designs and Intellectual Property
The workbook can be used as a framework for teaching, as well as for student independent working.
Each sub-section includes worksheets and practice questions to aid retention and understanding of how the content may be presented in the exam.
Progress can be tracked using the free tracker available from ACA Resources on TES.
https://www.tes.com/teaching-resource/a-level-dt-theory-tracker-12396290
The content in this workbook has been designed to meet the demands of the AQA A-level in Design and Technology/ Product Design. The content also closely meets the requirements for Eduqas/WJEC, OCR and Edexcel.
A-Level Design and Technology (Product Design)
Theory Section I (All 9 sections A through to I are also available)
Section I - Wider Issues and Standards
Student Workbook
This workbook comprehensively covers all content from section I of the theory, required for the A-Level DT exams.
I1 - Responsible Design
I2 - Design for Manufacture and Project Management
I3 - National and International Standards in Product Design
The workbook can be used as a framework for teaching, as well as for student independent working.
Each sub-section includes worksheets and practice questions to aid retention and understanding of how the content may be presented in the exam.
Progress can be tracked using the free tracker available from ACA Resources on TES.
https://www.tes.com/teaching-resource/a-level-dt-theory-tracker-12396290
The content in this workbook has been designed to meet the demands of the AQA A-level in Design and Technology/ Product Design. The content also closely meets the requirements for Eduqas/WJEC, OCR and Edexcel.