This is a fully-resourced revision lesson that uses a combination of exam questions, understanding checks, quick tasks and quiz competitions to enable students to assess their understanding of the sub-topics found within Topic P10 (Electricity and their circuits) of the Edexcel GCSE Combined Science specification. The sub-topics and specification points that are tested within the lesson include: Draw and use electric circuit diagrams Describe the difference between series and parallel circuits Recall that an ammeter is set up in series and a voltmeter is set up in parallel Explain that the electric current is the rate of flow of charge Recall and use the equation connecting potential difference, current and resistance Calculate the current, potential difference and resistance in series and parallel circuits Describe power as the energy transferred per second and is measured in Watts Describe the differences between alternating and direct current Recall that mains electricity uses alternating current and has a frequency of 50Hz Explain the difference between the function of the neutral and live wires Explain the function of the earth wire and fuses in ensuring safety Students will be engaged through the numerous quiz rounds whilst crucially being able to recognise those areas which require their further attention during general revision or during the lead up to the actual GCSE terminal exams

This is a fully-resourced revision lesson that uses a combination of exam questions, understanding checks, quick tasks and quiz competitions to enable students to assess their understanding of the content found within Module P1 (Matter) of the OCR Gateway A GCSE Combined Science specification. The sub-topics and specification points that are tested within the lesson include: Describe how the atomic model has changed over time Define density Measure length, volume and mass to calculate density Explain the differences in density between the different states of matter in terms of the arrangements of atoms and molecules Describe how physical changes differ from chemical changes Define the term specific heat capacity and distinguis between this term and specific latent heat Carry out calculations to apply the equations involving specific heat capacity and specific latent heat Students will be engaged through the numerous quiz rounds whilst crucially being able to recognise those areas which require their further attention during general revision or during the lead up to the actual GCSE terminal exams

This is a fully-resourced revision lesson, that is likely to be most effective when used over the course of a series of lessons, and has been designed to help students to revise and assess their knowledge of the content that is found in topics P4 (Waves and radioactivity), P5(Energy) and P6 (Global challenges) of the OCR Gateway A GCSE Combined Science specification. This is the content that will be assessed in paper 6 in the terminal exams. This revision lesson uses a combination of exam questions, understanding checks, quick tasks and quiz competitions to cover the following sub-topics and specification points: Wave behaviour The electromagnetic spectrum Radioactivity Work done Power and efficiency Physics on the move Powering Earth This lesson contains a big emphasis on the mathematical calculations that will be involved in these exams, and as a result students are challenged to recall the equations and to apply them. Students will be engaged through the numerous quiz rounds whilst crucially being able to recognise those areas which require their further attention during general revision or during the lead up to the actual GCSE terminal exams. A lot of the tasks have been differentiated so that students of all abilities can access the work and be challenged appropriately.

This is an engaging REVISION lesson which uses a range of exam questions, understanding checks, quick tasks and quiz competitions to enable students to assess their understanding of the content within topic 6 (Waves) of the AQA GCSE Physics (8463) specification. The specification points that are covered in this revision lesson include: Transverse and longitudinal waves Properties of waves Reflection of waves Sound waves Waves for detection and exploration Types of electromagnetic waves Properties of electromagnetic waves Visible light The students will thoroughly enjoy the range of activities, which include quiz competitions such as “Should you WAVE goodbye” where they have to determine whether a passage about waves is 100% correct or not whilst all the time evaluating and assessing which areas of this topic will need their further attention. This lesson can be used as revision resource at the end of the topic or in the lead up to mocks or the actual GCSE exams

This is fully-resourced REVISION lesson that contains an engaging PowerPoint (98 slides) and associated differentiated worksheets and has been designed to challenge the students on their knowledge of the content in TOPIC 4 (Electricity and magnetism) of the Cambridge IGCSE Physics specification. The lesson includes a wide range of activities which aim to motivate the students whilst they assess their understanding of the content and recognise those areas which need further attention. The lesson was designed to include as many sub-topics as possible but the following have been given a particular focus: Logic gates Series and parallel circuits and circuit calculations Resistors Diodes and their roles as rectifiers Fleming’s left-hand rule and the motor effect Transformers This lesson is suitable for revision purposes at numerous times of the year, whether it be at the end of the topic or in the lead up the mocks or actual IGCSE exams

This is a detailed lesson which looks at the topic of reaction times and guides students through calculating a reaction time using the results of the well known ruler-drop test. In addition, students will see how reaction times can be applied in athletics but also in the calculation of the thinking distance for drivers. The lesson includes an engaging lesson presentation (32 slides) and a student task worksheet. The lesson begins by introducing the key term, reaction time, and teaching students that the average reaction time is 0.2 seconds. Moving forwards, a step by step guide is used to show the students how to take the value for distance travelled by a ruler in the drop test and use the equations of motion and change in velocity equation to calculate the reaction time. There is a large mathematical element to the lesson which challenges the students ability to rearrange formula, convert between units and leave answers to a specified number of significant figures. The answers and methods in obtaining these are always displayed at the end of each task so that the students can assess their understanding and recognise where errors were made if any were. Students will have to follow the provided method to obtain 5 results in the ruler drop test and ultimately find out their own reaction time. The remainder of the lesson looks at how the thinking distance at different speeds can be calculated. This lesson has been written for GCSE students due to the high maths content but could be used with younger students of high ability.

This is a fully-resourced lesson that explores the meaning of irradiation and contamination and challenges the students to make links to the different types of radiation in order to state which type of radiation is most dangerous outside of the body and inside the body. This lesson includes an engaging lesson presentation (28 slides) and a differentiated worksheet which gives assistance to those students who find the task of writing the letter difficult. The lesson has been written to include real life examples to try to make the subject matter more relevant to the students. Therefore, whilst meeting the term contamination, they will briefly read about the incident with Alexander Litvinenko in 2006 to understand how the radiation entered the body. Moving forwards, students will learn that there are examples of consensual contamination such as the injection of an isotope to act as a tracer. At this point of the lesson, links are made to the topic of decay and half-lives and students are challenged to pick an appropriate isotope based on the half-life and then to write a letter to the patient explaining why they made their choice. The remainder of the lesson challenges students to decide which type or types of radiation are most dangerous when an individual is irradiated or contaminated and to explain their answers. This type of progress check can be found throughout the lesson along with a number of quick competitions which act to maintain engagement as well as introduce new terms. This lesson has been written for GCSE aged students

A concise lesson presentation (22 slides) and question worksheet, which together focus on the challenge of applying the equations of motion to calculation questions. Students are given this equation on the data sheet in the exam - therefore, this lesson shows them how they will be expected to rearrange in it four ways. For this reason, the start of the lesson revisits the skills involved in rearranging the formula, beginning with simple tasks and building up to those that involve indices as are found in this equation. Once students have practised these skills, they are challenged to answer 4 questions, although 1 is done together with the class to visualise how to set out the working. This lesson has been designed for GCSE students

An informative lesson which guides students through the commonly misunderstood topic of drawing free body diagrams and using them to calculate resultant forces. The lesson begins by ensuring that students understand that force is a vector quantity and therefore arrows in diagrams can be used to show the magnitude and direction. Drawing free body diagrams is poorly understood and therefore time is taken to go through the three key steps in drawing these diagrams. Each of these steps is demonstrated in a number of examples, so students are able to visualise how to construct the diagrams before they are given the opportunity to apply their new-found knowledge. The rest of the lesson focuses on calculating resultant forces when the forces act in the same plane and also when they are at angles to each other. Again, worked examples are shown before students are challenged to apply. Progress checks are written into the lesson at regular intervals so that students can constantly assess their understanding and any misconceptions can be addressed. This lesson has been designed for GCSE students

A fully-resourced lesson which includes a concise lesson presentation (16 slides) and accompanying worksheet that guides students through the use of the gravitational potential energy equation to calculate energy, mass and height. The lesson begins by challenging students to work out the factors involved in calculating gravitational potential energy having been given a scenario with some balls on shelves. The students will discover that mass and height affect the energy size and that a third factor, gravity constant, is involved. The rest of the lesson focuses on using the equation to calculate energy, mass and height. In terms of the latter, students have to carry out an engaging task to work out the height that three flags have to be hoisted to during a medal ceremony. This lesson has been written for GCSE students.

A fully-resourced lesson which focuses on using the kinetic energy equation to calculate energy, mass and speed. The lesson includes a lesson presentation (23 slides) which guides students through the range of calculations and accompanying worksheets which are differentiated. The lesson begins with the students being drip fed the equation so they are clear on the different factors involved. They are challenged to predict whether increasing the mass or increasing the speed will have a greater effect on the kinetic energy before testing their mathematical skills to get results to support their prediction. Moving forwards, students are shown how to rearrange the equation to make the mass the subject of the formula so they can use their skills when asked to calculate the speed. The final task of the lesson brings all of the learning together to tackle a set of questions of increasing difficulty. These questions have been differentiated so that students who need extra assistance can still access the learning. This lesson has been written for GCSE students

A fast paced lesson which focuses on the equation for work done and using this in calculations. The lesson includes a student-led lesson presentation and a question worksheet which together explore the different problems that students can encounter when attempting these questions and therefore acts to eliminate any errors. There is a big mathematical element to the lesson which includes the need to rearrange formula, understand standard form and to convert between units as this is a common task in the latest exams. Students will learn that some questions involve the use of two equations as they are needed to move from a mass to a force (weight) before applying the work done equation. The last part of the lesson looks at how work done is involved in the calculation for power. This lesson has been designed for GCSE students.

This lesson has been designed to help students to explain the relationship between current and resistance in thermistors and LDRs. This can be a topic which students do not engage with or understand well, so this lesson has tried to add engagement with useful tips to deepen their knowledge. A number of quick competitions are used to introduce key terms such as semiconductor and then the key points explained. Students are given an exemplary answer for the thermistor so they can see how their work should be set out when trying to explain the graph produced by a LDR. Progress checks have been written into the lesson at regular intervals so that students can assess their understanding and any misconceptions can be addressed. This lesson has been designed for GCSE students.

An engaging lesson which uses a range of tasks to ensure that students understand the meaning of the term, background radiation, and are able to name a number of sources of this type of radiation. The start of the lesson focuses on the definition of background radiation and the idea that is all around us is revisited again a number of times during the lesson. Through a range of activities and discussion points, students will meet the different sources as well as the % that they each contribute. It seemed appropriate to challenge some mathematical and scientific skills at this point so students will represent the data in a pie chart form. Related topics are discussed such as Chernobyl. Progress checks are written into the lesson at regular intervals so the students can constantly assess their understanding. This lesson is designed for GCSE students.

A fully-resourced lesson that explores how resistance, current and potential difference differ between series and parallel circuits. This knowledge needs to be sound in order for students to be able to carry out circuit calculations. The lesson includes a practical and task-based lesson presentation (24 slides) and an accompanying worksheet. The lesson begins by challenging the students to recognise the key difference between the two circuits, in that in a parallel circuits, the electrons can follow more than one route. Moving forwards, each physical factor is investigated in each type of circuits and students carry out tasks or calculations to back up any theory given. Helpful analogies and hints are provided to guide the students through this topic which is sometimes poorly understood. Students will be challenged to use the V = IR equation on a number of occasions so that they are comfortable to find out any of these three factors. Progress checks have been written into the lesson at regular intervals so that students are constantly assessing their understanding and any misconceptions can be addressed. This has been written for GCSE students, but could be potentially used with higher ability KS3 students.